The heating design decides how your mornings go. It sets how long you wait between a shot and steamed milk, how much fiddling it takes to get the brew temperature right, and what can wear out inside. Here are the four designs you'll see on the used market, from smallest to biggest.
Thermoblock and ThermoJet
A thermoblock heats water on the fly as it passes through a heated metal block or coil, so there's no big tank of hot water waiting. Breville's Barista Express uses a version it calls Thermocoil, with PID control holding the water at 200F. The Bambino Plus and Barista Pro use Breville's ThermoJet, which Breville says reaches extraction temperature in 3 seconds.
The upside is speed and size. You switch it on and you're making coffee almost straight away. Next to a Silvia, you get a shorter wait for hot water and less consistency than a full boiler gives. These machines also use Breville's 54mm portafilter instead of the 58mm cafe standard.
They suit one or two drinks at a time, a small counter, and anyone who'd rather not wait. Scale still matters here. Mineral deposits build up in a thermoblock just as they do in boilers, valves and tubing.
Single boiler
A single boiler machine has one boiler that does both jobs at two different temperatures. You brew at the lower setting, flip the steam switch, and wait for the boiler to climb to steam temperature. The Rancilio Silvia has a 0.3-liter brass boiler, and the Gaggia Classic Pro has a small brass boiler with an embedded heating element. Both take a 58mm portafilter.
Without a PID, a single boiler's thermostat lets the temperature swing up and down as the heater cycles. Owners work around that with temperature surfing. After steaming, you flip back to brew and run water through the group to pull the boiler down fast, then time your shot against the heating light. Pull right as the light comes on and you land around 198 to 200F. Wait 10 to 15 seconds after it and you're closer to 200 to 203F.
If you just wait, a non-PID single boiler takes 5 to 15 minutes to recover between shots. A single boiler suits someone who mostly drinks straight espresso, makes a milk drink now and then, and likes learning the machine. A PID kit makes the brew side far steadier, which we cover in our pump and PID guide.
Heat exchanger
A heat exchanger (HX) machine has one large steam boiler held at steam pressure. Fresh brew water runs through a tube inside that boiler and gets flash-heated on its way to the group. You can brew and steam at the same time, which is the whole appeal.
The catch is that brew water sitting in that tube overheats while the machine idles. That's what the cooling flush is for. Run water through the group and listen for hissing and sputtering, which means it's too hot. Once the stream runs even, you're at about 206 to 207F, so flush another 5 or 6 seconds to land near the 201 to 203F brew range, then give it 30 to 45 seconds to recover while you grind and tamp. After the machine has sat idle, a typical flush runs 10 to 15 seconds.
The Rocket Appartamento is a classic E61 HX with a 1.8-liter boiler, a vibration pump and a pressurestat, and its single gauge reads steam boiler pressure. The Lelit Mara X takes a different approach. It's also an HX with a 1.8-liter boiler, but Lelit added a second temperature probe at the group and three brew settings of 197, 201 and 205F, so you aren't guessing from sputter sounds.
An HX suits people who make milk drinks most days and don't mind a short flush as part of the routine.
Dual boiler
A dual boiler has a dedicated brew boiler and a separate steam boiler, each with its own temperature control. You set the brew temperature directly, steam whenever you like, and skip the flush. The Breville Dual Boiler has two stainless boilers, PID on the brew side and a 58mm portafilter. The Lelit Bianca pairs a 0.8-liter brew boiler with a 1.5-liter steam boiler, and the La Marzocco Linea Mini puts a 175ml brew boiler right on top of the group beside a 3.5-liter steam boiler.
Used, a dual boiler gives you more to check. You have two boilers to descale instead of one, and there's more control electronics to go wrong. They suit people making several milk drinks back to back, or anyone who wants to set a brew temperature and forget it.
Which one to buy used
- Pick a thermoblock Breville if you want speed, a small footprint and the least fuss.
- Pick a single boiler if you mostly drink espresso and like to tinker.
- Pick an HX if you want milk drinks on demand and can live with a flush.
- Pick a dual boiler if you make several milk drinks in a row or want the brew temperature dialed in to the degree.
Whichever you choose, the inspection matters more than the label. Our inspection guide covers what to test on each type.
Machines in this guide

Rancilio Silvia
It's built from commercial-grade parts and is one of the best-documented home machines ever made, so even a tired one can usually be put right.
Checklist and listings for the Rancilio Silvia →
Breville Bambino Plus
Owners keep them going for years, but Breville tells you not to open it for service, so you're buying on how it runs today.
Checklist and listings for the Breville Bambino Plus →
Lelit Mara X
The temperature trick lives in a control unit and sensors, so you're checking electronics as well as the usual E61 wear.
Checklist and listings for the Lelit Mara X →
Rocket Appartamento
The standard and Serie Nera are pressurestat E61 boxes with a vibe pump and almost no electronics, so a descaled one with fresh gaskets has little left to go wrong.
Checklist and listings for the Rocket Appartamento →
Breville Dual Boiler
It's a lot of machine, but steam boiler leaks and a blown steam boiler fuse are common repairs. A used one should reach temperature and steam on video.
Checklist and listings for the Breville Dual Boiler →Frequently asked
Do I need to do a cooling flush on a Lelit Mara X?
The Mara X manages brew temperature from a second probe at the group, with three set points, so you aren't flushing by ear the way you would on an older HX. Pull a few shots and taste before deciding how much flushing your cups need.
Is a dual boiler harder to look after than a heat exchanger?
There's more of it. You have two boilers to keep clear of scale and more electronics, so ask about water and service history even more carefully than on a single boiler or HX.
Is a thermoblock machine a bad first machine?
No. Breville's ThermoJet and Thermocoil machines heat fast and suit one or two drinks at a time. You trade some temperature consistency and the 58mm accessory world for speed and a small footprint.